You are hereGlacier Travel / Crevasse Rescue

Crevasse Rescue


In the event of a crevasse fall, you’ll need to have the equipment, skills, and knowledge to quickly perform a rescue, while working without outside help or resources. Speed is important to treat any injuries and to avoid the risk of hypothermia to the victim. Self sufficiency is a requirement because of remote locations and uncertain communications in the backcountry.




Crevasse Rescue Equipment

The following is a minimum list of equipment required for crevasse rescue and should be carried on each end of the rope:

  • 2 Anchors (flukes, pickets, or ice screws as appropriate)
  • 2 Pulleys
  • 2 Locking Carabiners
  • 3 Non-locking Carabiners
  • 1 Four-foot Runner
  • 1 Extra Prussik (in addition to the waist and foot prussiks carried for self rescue)

The Rescue

The first possibility in a crevasse fall is that the victim is conscious and uninjured. The victim can either climb or prussik out of the crevasse under his or her own power. The rescuer can help the victim by doing the following:

  1. Lowering a rope and hauling up the victim’s pack
  2. Padding the lip of the crevasse by sliding an ice axe, pack, skis, etc., under the loaded rope
  3. Dropping an extra rope so the victim can prussik up the second line
  4. Tying a series of loops at the lip so that the victim can use them as a rope ladder for climbing up and over the last few feet of the crevasse’s lip

The second scenario is that the victim is conscious but physically unable to rescue him or herself. The rescuer will have to haul this victim out of the crevasse, but may not have to rappel down, depending on the extent of the injuries. This section provides instructions for one technique to extract a victim from a crevasse.

The third possibility is that the victim is unconscious or has suffered an obviously serious injury, requiring the rescuer to rappel into the crevasse and administer first aid before hauling the victim out.

The worst-case scenario would be a rope team of two with one member unconscious some feet down in a crevasse. In this case, the rescuer would have to:

  1. Catch the fall
  2. Build an anchor
  3. Transfer the weight onto the anchor
  4. Approach the lip of the crevasse and assess the site
  5. Rappel to the victim and treat his or her injuries
  6. Improvise a chest harness to keep the victim upright
  7. Prussik back to the surface.
  8. Build a 6:1 pulley system
  9. Haul the victim out all the way over the lip of the crevasse

Your group should practice each of these skills until each of you is confident that you can perform them under the pressure of a real rescue.

Note: The rescuer should always make sure he or she is safely secured before approaching the lip of the crevasse to help the victim.

Catching a Fall

The difficulty of catching a fall is dependent upon how much slack there is in the rope. When your team is walking roped up, there should be only enough slack to let the rope lie on the surface of the snow (and not pull on the other members of the party). Never carry extra coils of rope in your hands, as they will add to the distance of the fall and increase the impact forces on both the rescuer and the victim. In an area where crevasses are expected and there is enough concern for the leader to start probing, the second person on the rope should keep the rope tight enough to raise it off the ground. This will further reduce the length of a fall by 2- to 3-feet.

In the event of a fall, the victim shouts "falling" if he or she has the time, and the other climbers take a step away from the fall to take up the slack before dropping to a self-arrest position. In a majority of falls, the victim will be caught by the rope before he or she has fallen deeper than the waist, or at worst, the shoulders. From this position, it should be relatively easy for the victim to climb back onto solid snow, and the rescuer can wait in a self-arrest position. Should a large bridge collapse or other circumstance arise where the victim is deep enough to be out of sight, the rescuer should immediately begin the process of building an anchor.

Building an Anchor

Once established in a secure self-arrest position, the rescuer needs to escape the system. Kick your feet into the snow or ice as deeply as possible until you feel comfortable working with your hands off the ice axe. From this position, you can safely build an anchor using a picket, fluke, or ice screw as conditions dictate. When satisfied with the anchor, get out your leg prussik (already on the rope), or a mechanical ascender with a long sling attached, and clip it into the anchor with a locking carabiner.

Locking Carabiner and prussik

Slowly transfer the victim’s weight onto the anchor by backing up toward the crevasse until all the weight is either on your leg prussik or mechanical ascender. During this process, you should stay in a self-arrest position to catch the victim (and yourself) in the event the anchor fails. Once the anchor has taken the weight, pull on the anchor with your own weight to test it while still remaining in a self-arrest position to catch a fall.

Deadman Snow Picket Anchor

By this time, your confidence in the anchor must be absolute. If the anchor fails after you leave the selfarrest position, the victim (and possibly you) will likely be killed.

Snow Fluke and Ice Screw Anchor

If the anchor is solid, you can now leave the self-arrest position to build another anchor behind the primary one. Clip this backup anchor into the locking carabiner already on the primary anchor. Remember: The area behind the primary anchor will not have been probed for crevasses, and you’re at risk of finding a crevasse of your own. You must stay clipped into the system until you have probed all the working areas and know the extent of crevasses in the area.

Snow Bollard and Snow Picket Anchor

Checking the Victim

The next priority is to check on the condition of the victim. Remove and uncoil the extra rope you are carrying, tie a Figure-8 knot on a bight as close as possible to the anchor, and clip it in. This will back up the prussik or mechanical ascender that the victim is hanging from, and give a solid anchor point for a rappel if that should become necessary. You must then estimate how far it is to the lip of the crevasse where the victim disappeared and measure that off on your rope, allowing a few extra feet of slack. Tie a Figure-8 on a bight and clip it to your harness. Next, a waist prussik or ascender should be switched from the victim’s rope to the slack line as close as possible to the anchor, and then clipped back into the harness. Your prussik or ascender will be your belay as you probe for crevasses and approach the lip of the hole, while the Figure-8 on the bight will serve as a backup should the belay fail.

Approach the hole where the victim disappeared by probing an area slightly to the side of the line to the victim. There is less chance of knocking snow or ice onto the victim if the hole/crevasse is not approached from directly above. Carefully probe the entire approach to the crevasse, looking for other crevasses and determining the extent of the lip over the victim. Slide the prussik or ascender as you go. After you’ve probed the area and deemed it safe, you’ll unclip from the rope to perform the rescue - it is critical that you are sure that the working area is safe.

When you’ve reached the lip of the crevasse, check on the victim. In the worst-case scenario of an unconscious or gravely injured victim, you’ll need to rappel down to the victim on the spare rope, using a prussik as a backup. Take with you a first-aid kit and any extra warm clothing or a sleeping bag to treat and bundle the victim. Pad the lip of the crevasse under your rappel line to prevent the rope from digging into the snow.

After you’ve treated the victim, make an improvised chest harness using a long sling and an extra prussik and turn the victim so that his or her back is facing the wall of the crevasse. This prevents the victim from suffocating by being dragged face first through the snow. The process of hauling out an unconscious victim can easily take over an hour. Be sure the victim is well bundled to prevent hypothermia before you begin your climb up to the surface. Retrieve any climbing hardware the victim has with them, particularly the prussiks, before you climb up.

The Hauling System

Once you’ve reached the surface, the next step is to set up the haul system. First the crevasse lip under the rope to the victim must be padded by sliding an ice axe, pack, skis, etc., under the loaded rope. If possible, anchor the padding to the top surface to prevent it from becoming dislodged and landing on the victim. Clip another carabiner into the carabiner attaching the foot prussiks to the anchor. At this point, it’s safe to unclip the Figure-8 knot attaching the rope to the anchor, and allow the victim to hang from the leg prussik or ascender momentarily. Untie the Figure-8 knot, put a pulley on the rope and clip it into the extra carabiner on the anchor (this is the static pulley ) Remove the self-belay waist prussik from the slack rope and install it on the rope to the victim about 2/3rds of the way to the edge of the crevasse. Place a section of the free rope through a pulley, and attach the pulley to the waist prussik with another carabiner.

Attempt to haul the victim up by pulling on the free end of the rope. This will be extremely difficult if working alone, but reasonable if two or more rescuers are pulling. As the victim is pulled up, the foot prussik may jam in the static pulley unless it is loosened so the rope slides freely through it.

Continue hauling until the moving pulley reaches the static pulley. Then, take the slack out of the foot prussik and slowly let the load out until the prussik takes the weight. Slide the waist prussik toward the victim as far as it is safe. Repeat this process until the victim is either stuck at the lip or out of the crevasse.

Note: This system gives the rescuer a 3:1 mechanical advantage, and it is possible to exert large forces on the victim and the anchors inadvertently. Any change in resistance in the haul line should be investigated immediately to avoid injury to the victim or overstressing the anchor.

If you are working alone, you’ll probably need more than a 3:1 mechanical advantage to haul a victim out. You can gain a better advantage by adding a 2:1 system to the 3:1, for an effective advantage of 6:1. Starting with the 3:1 system described before, find the end of the free rope and clip it in to the anchor with a Figure-8 knot (see figure 18-16). Then tie a second Figure-8 on a bight, as close to the moving pulley as possible. Using a carabiner, or another pulley if one is available, attach the free rope to the Figure-8 just mentioned. The rope coming out of the carabiner or pulley that was just installed becomes the haul line, and the victim is raised by pulling it in. Once the Figure-8 knot reaches the anchor, shift the weight to the leg prussik and move the waist prussik back toward the crevasse lip.

After several cycles, retie the Figure-8 loop that the last pulley is attached to, closer to the pulley. (It’s not necessary to untie the old knot, and it would be difficult anyway because it’s been under a load.) Repeat these steps until the victim is out of the hole.

Rescuers should know also how to construct a 2:1 pulley system independent of the 6:1 system described earlier. It is useful for providing a quick pull to help a conscious victim over the lip, and also to haul victims all the way out if there is a large group of people to do the hauling.

  1. Build an anchor and clip the free end of a rope into it.
  2. Install a pulley on the rope with a locking carabiner attached.
  3. Lower this pulley to the victim on a bight of rope and clip it to his or her harness.
  4. Haul on the free end of the rope until the victim is retrieved. Have the free end of the rope belayed by an extra rescuer or attach a prussik between the rope and the anchor, and slide it up the rope to provide a belay as the line is hauled in.

Generally, the hardest part of extracting an unconscious victim from a crevasse is getting him or her over the lip. Once the victim has been raised to the lip, you’ll have to attach a prussik to the haul line and go to the edge. Carefully excavate the snow at the lip until there is a gradually sloping ramp to haul the victim onto. If the haul rope is under tension, a vertical tug on the victim will frequently cause him or her to slide up the ramp because of the rope stretch. You may have to repeat this process several times before the victim is all the way up.

The Climber's Bible